• Contact us +91 9898816341
  • Fuel Injection Gear Pump

    PEC-FIG-150L to 600-L

    PEC-FIG-150R to 600-R

    Each Model provided port size being 1/2" suction x 1/2" delivery being 150LPH,300 LPH, 450 LPH and 600 LPH.

    Also provied with internal by Pass and 1/4" BSP external By Pass. They are available both in Clockwise-R and Anticlockwise-L Direction. Speed allowed for these pumps are both 1440 RPM and 2880 RPM

    PEC-FIG-60/90/120-L

    PEC-FIG-60/90/120-R

    Each Model provided port size being 3/8" BSP suction * 3/8" BSP delivery capacity. Being 60LPH, 90 LPH & 120 LPH provided with internal by pass and 1/4" BSP external bypass. They are availble both in clockwise-R and anticlockwise-L direction.

    Speed allowed for this pump is only 2880 RPM

    PEC-FIG-1000 to 2500-L

    PEC-FIG-1000 to 2500-R

    Each Model provided port size being 3/4" BSP suction * 3/4" BSP delivery capacity. Being 1000 LPH, 1500 LPH & 2500 LPH provided with internal by pass and 3/4" BSP top external bypass & 3/8" BSP side external bypass. Speed allowed for this pump is only 1440 RPM. They are availble both in clockwise-R and anticlockwise-L direction.

    • Pumps most suitable for raod construction machinery.
    • Boilers, Oil burner, Hydraulic Drive.
    • Pressure and transfer pump.
    • Booster pump for diesel locomotive.
    • Pump for forced feed lubrication.
    • Filter Pumping
    • Pump for lubrication oil and hydraulic oil.
    • Pump suitable for LDO, FO, HSD & LSHS
    Model Inlet & Outlet Size Capacity Iph Speed rpm Recommended Motor hp at
    5 kg/cm2 15 kg/cm2 30 kg/cm2
    PIG-50 ½ Χ ½ 150 1440 0.25 HP 0.75 HP 1.5 HP
    300 0.25 HP 0.75 HP 1.5 HP
    450 0.5 HP 1 HP 1.5 HP
    600 0.5 HP 1 HP 2 HP
    PIG-75 ¾ Χ ¾ 1000 0.75 HP 2 HP 3 HP
    1500 0.75 HP 2 HP 3 HP
    2000 1 HP 3 HP 5 HP
    2500 1 HP 3 HP 5 HP

      Instruction:

      For trouble free of pump following points are to be considered carefully-
    • True alignment while mounting pump
    • No any water particle allowed with oil
    • Non lubricant liquid should not be used
    • keep direction of rotation of pump and suction and delivery connection as
      shown on pump (R= Clock Wise, L= Anticlockwise viewed from shaft end)
    • They should not be need for handling abrasive or corrosive or liquid with solid mater.

    General Specification

    "PARAS" Fuel Injection Gear Pumps are positive displacement gear pumps. Available with without built in pressure relief valve. Pimps are of High Pressure and Internal Lunrication system is so designed that the liquid running through the pump acts as a lubricant. Pumps are designed for wide range of applications. They should not be used for handling abrasive liquids with solid matter. Pumps are self priming and give maximum vaccum of 610-660 mm of Hg. They can handle non-corrosive and non abrasive liquids of maximum vicosity of 455 cents-stocks(CS) and temperature 200 degree celcius.

      Salient Features

    • Due to static 'O' Ring there is no leakage.
    • Low cost maintenance.
    • Rotors & Gears are used with hardend and ground which gives good efficiency and more durability.
    • We have specially provided enough lubrication system to oil seal, which increase the life of oil seal.
    • Available with or without built in pressure relief valve and external bypass.
    • We have also developed pump suitable for Kerosean
    • We try our best to fulfill customer's requirements and delivery as fast as possible.